Cisco has updates available to handle three high-rated vulnerabilities its Cisco IOS XR software where an attacker could exploit one of these vulnerabilities to take control of an affected device.

In one issue, there is a vulnerability in the Layer 2 Ethernet services of Cisco IOS XR Software. The issue could allow an unauthenticated, adjacent attacker to cause the line card network processor to reset, resulting in a denial of service (DoS) condition.

The vulnerability is due to the incorrect handling of specific Ethernet frames received on line cards that have the Layer 2 services feature enabled. An attacker could exploit this vulnerability by sending specific Ethernet frames through an affected device.

A successful exploit could allow the attacker to cause the ingress interface network processor to reset. That could result  in a loss of traffic over the interfaces supported by the network processor. Multiple resets of the network processor would cause the line card to reset, resulting in a DoS condition.

Schneider Bold

Cisco released software updates that address this vulnerability, according to an advisory. There are no workarounds that address this vulnerability.

This vulnerability affects the following Cisco products if they are running a vulnerable release of Cisco IOS XR 64-bit Software and have an affected Layer 2 transport configuration enabled:

  • ASR 9000 Series Aggregation Services Routers that have a Lightspeed-based or Lightspeed-Plus-based line card installed
  • ASR 9902 Compact High-Performance Routers
  • ASR 9903 Compact High-Performance Routers
  • IOS XRd vRouters
  • IOS XRv 9000 Routers

As a mitigation, either remove load-balancing flow src-dst-ip, if configured, or change the service policies so they do not examine the IP header.

Meanwhile, in another issue, there is a vulnerability in the SSH client feature of Cisco IOS XR Software for Cisco 8000 Series Routers and Cisco Network Convergence System (NCS) 540 Series and 5700 Series Routers that could allow an authenticated, local attacker to elevate privileges on an affected device.

This vulnerability is due to insufficient validation of arguments included with the SSH client CLI command. An attacker with low-privileged access to an affected device could exploit this vulnerability by issuing a crafted SSH client command to the CLI. A successful exploit could allow the attacker to elevate privileges to root on the affected device.

Cisco released software updates that address this vulnerability, according to an advisory. There are no workarounds that address this vulnerability.

This vulnerability affects the following Cisco products if they are running a vulnerable release of Cisco IOS XR Software:

  • 8000 Series Routers
  • IOS XRd Control Plane
  • IOS XRd vRouter
  • NCS 540 Series Routers that are running the NCS540L images
  • NCS 5700 Series Routers (NCS-57B1-5DSE-SYS, NCS-57B1-6D24-SYS, and NCS-57C1-48Q6-SYS)

In the third issue, there is a vulnerability in the PPP over Ethernet (PPPoE) termination feature of Cisco IOS XR Software for Cisco ASR 9000 Series Aggregation Services Routers. It could allow an unauthenticated, adjacent attacker to crash the ppp_ma process, resulting in a denial of service (DoS) condition.

This vulnerability is due to the improper handling of malformed PPPoE packets received on a router running Broadband Network Gateway (BNG) functionality. There would need to be PPPoE termination on a Lightspeed-based or Lightspeed-Plus-based line card. An attacker could exploit this vulnerability by sending a crafted PPPoE packet to an affected line card interface that does not terminate PPPoE. A successful exploit could allow the attacker to crash the ppp_ma process, resulting in a DoS condition for PPPoE traffic across the router.

Cisco released software updates that address this vulnerability, according to an advisory. There are no workarounds that address this vulnerability.

This vulnerability affects Cisco ASR 9000 Series Aggregation Services Routers running a vulnerable release of Cisco IOS XR Software and have all of the following characteristics:

  • A Lightspeed-based or Lightspeed-Plus-based line card installed
  • BNG with PPPoE termination enabled
  • At least one interface or sub-interface with PPPoE enabled on an affected line card
  • At least one interface or sub-interface with PPPoE not enabled on an affected line card

Click here for more security updates for Cisco products.

Pin It on Pinterest

Share This