Siemens has updates available to handle an uncontrolled resource consumption vulnerability in its KTK, SIDOOR, SIMATIC, and SINAMICS products, according to a report with CISA.

Successful exploitation of this remotely exploitable vulnerability, which Siemens self-reported, could create a denial-of-service condition. In addition, an attacker with low skill level could leverage the vulnerability.

In the vulnerability, the Interniche-based TCP stack can end up forced to make resource intense calls for every incoming packet, which can lead to a denial of service. CVE-2019-19300 is the case number assigned to this vulnerability, which has a CVSS v3 base score of 7.5.

The following Siemens products suffer from the issue:

Schneider Bold
  • KTK ATE530S: All versions
  • SIDOOR ATD430W: All versions
  • SIDOOR ATE530S COATED: All versions
  • SIDOOR ATE531S: All versions
  • SIMATIC ET200SP IM155-6 MF HF: All versions
  • SIMATIC ET 200SP Open Controller CPU 1515SP PC (incl. SIPLUS variants): All versions prior to 2.0
  • SIMATIC ET 200SP Open Controller CPU 1515SP PC2 (incl. SIPLUS variants): All versions prior to 2.0
  • SIMATIC ET200MP IM155-5 PN HF (incl. SIPLUS variants): Versions 4.2 and later
  • SIMATIC ET200SP IM155-6 PN HA (incl. SIPLUS variants): All versions
  • SIMATIC ET200SP IM155-6 PN HF (incl. SIPLUS variants): Versions 4.2 and later
  • SIMATIC ET200SP IM155-6 PN/2 HF (incl. SIPLUS variants): Versions 4.2 and later
  • SIMATIC ET200SP IM155-6 PN/3 HF (incl. SIPLUS variants): Versions 4.2 and later
  • SIMATIC MICRO-DRIVE PDC: All versions
  • SIMATIC PN/PN Coupler (incl. SIPLUS NET variants): Versions 4.2 and later
  • SIMATIC S7-1500 CPU family (incl. related ET200 CPUs and SIPLUS variants): All versions prior to 2.0
  • SIMATIC S7-1500 Software Controller: All versions prior to 2.0
  • SIMATIC S7-300 CPU family (incl. related ET200 CPUs and SIPLUS variants): All versions
  • SIMATIC S7-400 PN/DP V7 and below CPU family (incl. SIPLUS variants): All versions
  • SIMATIC S7-410 CPU family (incl. SIPLUS variants): All versions
  • SIMATIC TDC CP51M1: All versions
  • SIMATIC TDC CPU555: All versions
  • SIMATIC WinAC RTX (F) 2010: All versions
  • SINAMICS S/G Control Unit w. PROFINET: All versions

The product sees use in the chemical, energy, food and agriculture, and water and wastewater systems sectors. It also sees action on a global basis.

No known public exploits specifically target this vulnerability. However, an attacker with low skill level could leverage the vulnerability.

Siemens recommends applying updates if available:

  • SIMATIC ET 200SP Open Controller CPU 1515SP PC (incl. SIPLUS variants): Update to v2.1.7
  • SIMATIC ET 200SP Open Controller CPU 1515SP PC2 (incl. SIPLUS variants): Update to v20.8
  • Update to v2.8
  • SIMATIC S7-1500 Software Controller: Update to v20.8

Siemens has not identified any specific mitigations or workarounds and recommends following their general security recommendations. As a general security measure, Siemens recommends protecting network access to devices with appropriate mechanisms. In order to operate the devices in a protected IT environment, Siemens recommends configuring the environment according to the Siemens operational guidelines for Industrial Security and following the https://www.siemens.com/cert/operational-guidelines-industrial-security.

For additional information, please refer to Siemens Security Advisory SSA-593272.

Pin It on Pinterest

Share This