Modbus continues to be the most popular and exposed OT protocols for attackers to take advantage of, but it is not the only one, a new report found.

Additionally, it appears it is not enough to focus on the “popular” protocols for which the most common attack tools are available, according to the 2024 Global Threat Report by Forescout Research with Vedere Labs.

Most data used for analysis comes from the Vedere Labs Adversary Engagement Environment (AEE), a set of honeypots on the open Internet luring attackers and recording their interactions. Data points in the AEE end up labeled attacks. They can represent a multitude of malicious actions, including port scanning and brute forcing. The AEE recorded more than 900 million attacks between January and December 2024. A subset of these attacks contains exploits – attempts to exploit vulnerabilities.

In the wide ranging report, researchers found attacks on industrial automation protocols increased from 71 percent to 79 percent, utilities decreased from 28 percent to 12 percent and building automation increased from 1 percent to 9 percent.

The most relevant increase, the researchers said, is in the building automation category – especially when researchers looked at the new protocols under attack. Last year, they saw how attacks on building automation focused on exploiting vulnerabilities rather than interacting directly with protocols.

Schneider Bold
OT Protocols Pique Interest

This year, rather, they saw the interest in building automation protocols is increasing as attackers are still exploiting vulnerabilities on those devices (as evidenced by the table in section 2.5).

The following is the distribution of attacks targeting OT protocols:

  • Modbus, the most popular and most often exposed, OT protocol increased from 33 percent to 40 percent
  • EtherNet/IP increased from19 percent to 28 percent
  • Step7, used by Siemens devices, decreased from 18 percent to 8 percent
  • DNP3, often used in utilities, decreased from 18 percent to 8 percent
  • BACnet, used for building automation, is the fifth most attacked protocol with 7 percent of total attacks

Overall, the data paints a picture of a heavy interest in Modbus and more fragmented interest in a diversity of other protocols.

In the end, researchers said monitoring the traffic to and from OT devices is now as critical as monitoring IT traffic.

OT Protocols Attacked

Chart shows levels of attacks on industrial automation protocols increased to 79 percent, utilities decreased to 12 percent and building automation increased to 9 percent.
Source Forescout

Furthermore, attackers are constantly probing OT/ICS assets for weaknesses. Organizations will be blind to them because they do not have visibility into their OT/ IoT infrastructure. The truth is that building automation, and protocols such as Modbus, are now in almost every organization and are a target for attackers.

Cybersecurity Pillars

As a point of fact, Forescout researchers said organizations should focus on three key pillars of cybersecurity at a more strategic level:

Risk and exposure management: Start by identifying every asset connected to the network, its criticality, credentials, open ports and general security posture.

Change any default credentials and use strong, unique passwords for each device. Next, unused services should end up disabled and vulnerabilities patched to prevent exploitation. Finally, focus on risk mitigation using automated controls that do not rely only on security agents and apply to the whole enterprise.

Network security: Do not expose unmanaged devices directly to the Internet. Segment networks to isolate IT, IoT and OT devices, limiting network connections to only specifically allowed management and engineering workstations, or among unmanaged devices that need to communicate.

Segmentation should not happen only between IT and OT, but even within IT and OT networks to prevent lateral movement and data exfiltration. Restrict external communication paths and isolate or contain vulnerable devices in zones as a mitigating control.

Threat detection and response: Use an IoT/OT-aware, DPI-capable monitoring solution to alert on malicious indicators and behaviors, watching internal systems and communications for known hostile actions such as vulnerability exploitation, password guessing or unauthorized use of OT protocols. You should block anomalous and malformed traffic, or alert network administrators to its presence.

Beyond network monitoring, threat detection and response solutions collect telemetry and logs from a wide range of sources including security tools, applications, infrastructure, cloud and other enrichment sources, to correlate attack signals, generate high-fidelity threats for analyst investigation and provide the ability to automate response actions across the enterprise.

Click here for more on the report.

Pin It on Pinterest

Share This